您当前的位置:华人螺丝网 >> 螺丝供应 >> Sandstrom 9A沙暴涂层

Sandstrom 9A沙暴涂层

更新时间:2016-07-04    有效期:60个月     加入收藏

Sandstrom 9A沙暴涂层

详细的产品描述:

Where parts may be subjected to frequent disassembly Net Wt./ Gallon 9.5 lbs. + .2 lb. Solids Content 40% minimum (By Wt.) Viscosity 40 - 46 sec (#1 Zahn cup @ 770F) Flash Point 440F+ 20F Setaflash Operating Temp. Range -3200F to +5000F Vehicle Type Epoxy-Phenolic VOC 5.5578 lbs./gal. minus water (Theoretical) Specifications: SAE Spec AS5272C PRI QPL AS5272 type 2 Wear Life: 496 Minutes average ASTM D2625 A NOTICE Before using this product, read all warnings and safety information printed on the label, the Material Safety Data Sheet, and the Technical Info-Guide STIRRING IMPORTANT! THIS LUBRICANT CONTAINS HEAVY PIGMENTS WHICH SETTLE RAPIDLY. THEREFORE, IT SHOULD BE STIRRED THOROUGHLY BEFORE USE AND CONTINUOUSLY DURING APPLICATION. THINNING For spraying* - Use 2 parts 9A to 1 part PM solvent. For dipping* - Use slow-drying thinner mixture of PM and PMA, blended 1:1, as to provide proper run-off characteristics. The suggested starting point is 4 parts 9A to 1 part thinner mixture. *By volume. APPLICATION SANDSTROM 9A should be sprayed or dipped to the desired film thickness (usually .0003 to .0007 inches). Allow parts to flash off at least 30 minutes at 770F +50F. BAKING BAKING 4000F (2040C) FOR ONE (1) HOUR in a forced draft oven will yield optimum corrosion protection and wear life. IMPORTANT! The hour begins when the part has reached 4000F (2040C), NOT when it is placed in the oven. In cases of very thick metals, an extra hour may be required to bring the part up to the proper temperature. Thermocouples may be used to determine the true temperature of the metal. However, if the metallurgical properties are adversely affected by baking at this temperature (i.e., ALUMINUM, in some cases), we would recommend use of SANDSTROM LC-300 Heat Curing Lubricant which cures at 3000F (1490C) in ONE (1) HOUR. SANDSTROM 099 could also be used as it will cure in temperatures ranging from 3000F to 4000F. IT IS IMPERATIVE TO USE A PROPERLY VENTED OVEN (DIRECT VENT TO THE OUTSIDE). CLEANUP Use the same solvents for cleaning tools as are recommended for thinning. REMOVAL OF SANDSTROM 9A In the event it is necessary to remove Sandstrom 9A, physical removal is best (such as grit blasting, sanding, or grinding). **Strict compliance to the instructions given in Surface Treatment, Stirring, and Baking is essential to obtain optimum results. WARNINGS: Constant stirring is imperative for best results. Caution: Flammable. Keep away from sparks and open flame. Use with adequate ventilation. Avoid prolonged breathing of vapors. If swallowed--DO NOT INDUCE VOMITING. Contains Toluene and Phenolic and Epoxy Resins. Call physician immediately. GENERAL Sandstrom 9A is a paint-like material consisting of lubricative pigments dispersed in a thermosetting resin system thinned with appropriate solvents. For maximum service, the APPLICATION INSTRUCTIONS MUST BE FOLLOWED CLOSELY. The lubricant is flammable and the safety precautions usually followed when using flammable materials must be observed. FILM THICKNESS AND ENGINEERING TOLERANCES As supplied, SANDSTROM 9A will yield a film thickness of about .0005 inches per dip coat. Usually engineering tolerances will permit necessary minimum film buildup of .0002 to .0003 inches without interference. If excess buildup does occur and a force fit is necessary, burnishing lightly will assist in mating the parts. The remaining excess will be worn away in the first few cycles of operation. Whenever possible, the proper tolerances should be

快速询价

内容:
登录后方可询价.   马上登录免费注册

联系方式

公司名称: 比尔安达(上海)润滑材料有限公司网络部 加入到通讯录
核心产品:
表面处理机械设备紧固件行业表面处理修改/纠正
联  系  人: 郁先生 先生 (销售部) 打电话给我时,请一定说明在华人螺丝网看到的,谢谢!
电        话: 86-021-61486659
传        真: 86-021-61486662
手        机: 18221041697
邮        箱: 18221041697@sina.cn
地        址: 宝山区长建路198号1号厂房
网        站: www.billanda.com
Q        Q: 跟我QQ洽谈

比尔安达(上海)润滑材料有限公司网络部

产品信息
供应产品 更新时间 有效期 浏览数
沙暴飞机紧固件涂层 2014-08-26 1825天 172
供应模具ws2干膜润滑涂层 2014-08-28 1825天 258
上海二硫化钨干膜涂层 2014-08-30 1825天 345
供应everlube二硫化钼涂层 2014-08-30 1825天 287
供应everlube6102G聚四氟乙烯涂层 2014-08-30 1825天 211
供应everlube,mos2涂层 2014-08-28 1825天 259
everlube6219涂层 2016-06-24 180天 306
ws2干膜润滑涂层 2016-07-01 1825天 315
供应模具干膜润滑ws2涂层 2016-06-24 1825天 361
供应德国福斯可力特摩gleitmo615润滑剂 2015-04-14 1825天 231